 |
|
|
 |
|
 |
Home > System application |
|
 |
|
|
| AT800 RF Pre-conformance Test System |
| AT800 System is ideal of RF Pre-Conformance & Design Verification test tool for Wireless Terminals (Mobile Phones, etc.) with different wireless technologies.
Furthermore, AT800 is all-in-one system that supports multiple wireless standards on the same system hardware and software platform at the same time.
AT800 is affordable RF Pre-conformance test system with proven high level test accuracy.
AT800 System is ideal RF quality assurance solution for Wireless Terminal Manufacturers, Test Labs, as well as OEM Manufacturers. |
|
|
 |
|
|
|
| AT800-TX Wireless Transmitter Pre-Conformance Test System |
| AT800-TX is dedicated test system for verifying the transmitter (TX) performance of wireless terminals of different wireless technologies.
AT800-TX is low-cost TX design verification test system which fully utilizes the customer's Wireless Tester & Spectrum Analyzer on hand, to accelerate the time-consuming TX test cases, such as Spurious Emission. |
|
|
|
|
|
|
| AT800-RX Wireless Receiver Pre-Conformance Test System |
| AT800-RX is dedicated test system for verifying the receiver (RX) performance of wireless terminals of different wireless technologies.
AT800-RX is low-cost RX design verification test system which fully utilizes the customer's Wireless Tester & Signal Generators on hand, to accelerate the time-consuming RX test cases, such as Blocking Performance. |
|
|
|
|
|
|
| AT600 CTIA OTA Test System Software |
| AT600 OTA (Over The Air) Test System Software is ideal tool for verifying Antenna performance of wireless terminals, according to the following standards issued by CTIA (Cellular Telecommunication and Internet Association).
AT600 is affordable OTA Test System Software for CTIA Conformance & Pre-Conformance Testing, for Wireless Terminal Manufacturers as well as Test Labs. |
|
|
|
|
|
|
| AT600-OATS Open Area OTA Test System |
| The ultra expensive big size RF Anechoic Room is required for far-field OTA (Over The Air) testing on DUTs with lower frequency (longer wavelength) and larger size, such as HF/VHF Radio Antennas and Base Station Smart Antennas. OATS (Open Area Test Site) is a reasonable alternative in the industry. AT600-OATS system software is affordable open area far-field OTA test system software for Smart Antenna and other large DUTs.
AT600-OATS is a versatile test system software platform not only for Passive Antenna Patttern Test, but also for Active TRP / TIS Test, as well as OSE and EMI Radio Spurious Test. |
|
|
|
|
|
|
| AT600-FR Full Ring MIMO OTA Test System Software |
| AT600-FR System Software implements the Full Ring MIMO OTA test method, based on the Multi-Channel Emulator EB (Elektrobit) PropSim F8.
Although the official MIMO OTA standard has not been finalized yet, the Full Ring test method is the most widely accepted methodology by the industry and the customers, such as Nokia, LG, Vodafone, NTT Docomo, etc.
AT600-FR software supports all the existing MIMO technologies, for all the MIMO Channel Models.
AT600-FR is affordable MIMO OTA test system softare for Wireless Terminal Manufacturers and Test Labs. |
|
|
|
|
|
|
| AT600-SC Single Cluster MIMO OTA Test System Software |
| AT600-SC System Software implements the Single Cluster MIMO OTA test method, based on the Multi-Channel Emulator EB (Elektrobit) PropSim F8.
Comparing with Full Ring test method, Single Cluster is suitable for implementation in customer’s existing small Anechoic Chambers, which is much more cost-effective.
Therefore, AT600-SC is the ideal entry level MIMO OTA Test System with the best price/performance ratio for Wireless Terminal Manufacturers. And the system is upgradable from AT600-SC to AT600-FR Full Ring MIMO OTA Test System. |
|
|
|
|
|
|
| AT500 Wireless Terminal Production Test Systems |
| Wireless Terminals, such as mobile phones, smart phones and PADs, are integrating more and more functions including Wireless Technologies such as 2G/3G/WiFi/Bluetooth/A-GPS/FM, etc.
However, the product's life cycle is becoming shorter and shorter, with much more competition and less profit margin, while the labor cost of production operators is rising sharply.
Therefore, the wireless terminal manufacturers are pushing to reduce production cost even more imperatively.
Ascentest AT500 Series Production Systems are the right solutions to those needs for production cost reduction without compromising product quality, by implementing production automation and informatization, making full use of expensive instruments and optimizing production procedures. |
|
|
|
|
|
|
| AT510 RF Test System |
| AT510 is RF Calibration / Final Test System for Production of Wireless Terminals, such as mobile phones, smart phones and PADs, etc.
The system implements Non-Signaling test method to improve production efficient for Bard Test of 2G/3G/WiFi/Bluetooth/A-GPS/FM, etc.
AT510 system supports both old and new models of instruments, to increase the utilization of the expensive test equipment, and improve the flexibility for customer’s production investment plan, such as instruments rental.
AT510 system reduces the cost of production not only by improving efficiency, but also by optimizing test procedures, stabilizing the product quality, and reducing the need for operators in production lines.
AT510 system can be controlled by Ascentest PIMS (Production Information Management System) for data collection and production / factory management (Shop Floor Management), to upgrade the production management level. |
|
|
|
|
|
|
| AT550 Machine Vision Test System |
| AT550 is automatic vision inspection test system, which is ideal tool for checking appearance of different products, including consumer electronics and other general products, such as components, connectors, labels, bottles, tubes, medicine capsules, mechanical parts, gear wheels, etc.
Typical Applications for vision inspection of mobile phones and other Wireless Terminals are MMI (Man Machine Interface) Testing.
AT550 system greatly improves the efficiency and accuracy for appearance inspection. It also reduces production cost by requiring lesser operators and avoiding the eye weariness of operators.
AT550 system can be controlled by Ascentest PIMS (Production Information Management System) for data collection and production / factory management (Shop Floor Management), to upgrade the production management level. |
|
|
|
|
|
